- #Phoenix awardbios cmos setup utility storage controller software
- #Phoenix awardbios cmos setup utility storage controller password
- #Phoenix awardbios cmos setup utility storage controller Pc
The results can be analysed with Norton-Utilities from version 3.0, for example. If the option is activated, the system will issue a warning regarding an impending crash, for example.
#Phoenix awardbios cmos setup utility storage controller software
Among other things, in conjunction with suitable software this technology can be used to detect hard disk read or speed problems at an early stage. (Self Monitoring Analysis and Reporting Technology) is implemented in modern hard disks. OS Select For DRAM > 64 MBįor OS/2 systems with more than 64 MB RAM, option OS/2 should be used. Setting options: 1.1 or 1.4 For older operating systems 1.1 should be used, otherwise leave as 1.4. This option specifies what MPS version (Multi-Processor Specification) is used by this board. Settings: Enabled or Disabled MPS Version Control For OS APIC mode offers extended IRQ resources (depending on the board). According to the PC2001 regulations, the system may run in APIC mode. This parameter switches the APIC Controller (Advanced Programmable Interrupt Controller) on or off.
#Phoenix awardbios cmos setup utility storage controller password
If the SETUP option is selected, a password is only required for accessing the BIOS.
#Phoenix awardbios cmos setup utility storage controller Pc
If the SYSTEM option is selected, a password has to be entered during PC start-up. This parameter specifies the option for which a password applies. The options are 250, 500, 750 or 1000 milliseconds. This value determines when the key function is activated after a key is pressed. Specifies the repetition rate of the keyboard when a key is pressed. The settings can also be specified via the operating system. If Disabled, the values are set to 6 characters per second, with a keyboard delay of 250 ms. This parameter is used to specify whether the options Keyboard Typematic Speed, Delay Before Keys Repeat, Typematic Rate or Typematic Delay are available. DOS will anchor itself there, if DOS=High is inserted in Config.sys. The first 64 K Block above 1 MB can be accessed in standard mode via address line A20. This option may speed up older computers. With the Normal setting it is accessed via the keyboard controller. This should be set to Fast, in order to activate access through the chipset. Gate A20 Optionĭefines how the memory above 1MB is accessed. "First Boot Device", "Second Boot Device" or "Third Boot Device". The Enabled setting enables the BIOS to try all three types, i.e.
This option offers two choices: Enabled or Disabled. First set the drive to be used as boot drive. This setting is used for booting, if the first and second boot device are not available. This setting is used for booting, if the first boot device is not available.
Here you can specify which drive should boot first. However, not all POST tests are carried out. Booting will be up to 50 seconds faster with 64 MB RAM or more. If this option is enabled the computer will start significantly faster. Setting options: Enable (standard) - cache activated, Disabled - cache deactivated. If the CPU requests data, the system transfers theses data from the main DRAM to the cache memory for faster access by the CPU. The cache memory is an additional memory that is substantially faster than the conventional DRAM (system memory). after reinstallation of an operating system, is confirmed), Disabled (boot sectors are not verified). Setting options: Enabled (a virus warning may appear until it is acknowledged with Confirm or switched off (Disabled)), Confirm (a required boot sector modification, e.g. On start-up the boot sectors are checked for changes since the last start. This menu item can be used for setting the CPU behaviour for thermal profiles. ↑ ↓ → ← :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:Helpį5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults CPU Feature The hard disk data (size, number of cylinders, heads, sectors, pre-compensation and home position of the heads when the disk is switched off) are displayed automatically for the connected hard disk. This menu is used to set the data for the hard disk connected as master to the first IDE bus.
0 kommentar(er)
